Sunday 20 August 2017

Singer 222K Featherweight - Darning and Patching Trousers

Hello

I had another play with my new to me 222K.  It's a novelty for me to have a machine with a free arm.

First fixed my partner's work jeans, he had torn the knee when doing some work in the garage on his car.


Pulled the jeans leg over the free arm then using a rectangle patch that I had already made.  Sewed 2 sides on the machine, there was just enough wiggle room to turn the corner.   Then turned the jeans around so the waist end went on the freearm first, sewed the other 2 sides.


Turned the jeans inside out, tucked in the frayed edges and machined round so that he wouldn't catch his toes when putting them the jeans on.


His tatty jeans will last a bit longer.


The 222K was powerful enough to sail through the layers of thick fabric.  Brill.

Onto the darning, my lovely customer Don who is 85 said he was going to re-darn his work trousers.  So I offered my services as darner.  Was really keen to try out my new darning hoop recently bought on Ebay.


Took out all the old darning threads.  Glued a patch on the back of the tear so that I had something to darn to (it held the tear together as well).  I left the frayed threads on the edges of the tear, you are supposed to tidy the edges.


Original 222K hoop and darning foot.


The hoop snaps together.


It has a post on the back that slots into a square hole on the bed, then the hoop swings round.


Material goes over bottom hoop then the top clips over the fabric except as this was thick fabric, it was tricky to get it to clip together but just holding the hoop held the top in place.  When you put the foot on, there is only one place to put it, as you drop the foot the lever hardly drops down, this is normal.  It drops enough to engage the tension.  There is no mention of this in the instructions so a bit confusing when you first use it as you are used to the lever dropping right down.  There is a little sticky out bit lever above the spring, you can use this to lift the foot up to get the fabric and hoop underneath.

YOU MUST DROP THE FEED DOGS BEFORE SEWING. Its easy on the 222K there is a lever next to the stitch length lever.  Set the stitch length to 12.

The hoop moves easily in all directions whether is up and down or side to side, its a joy to use.

Pick up your bottom thread and bring to the top by turning the hand wheel.  Holding both ends start sewing, cutting off the ends when you have done a few stitches.  Sew around the edges of the tear, as you look at the picture below sew up and down fairly close together, once you get the end of the space in the hoop, go back the way you came sewing side to side.  If the tear is big like this one, you will have to move the fabric in the hoop.  It's easy to cut the threads off, reset the hoop and start again, this tear took 3 hoop moves.



My first darn on the 222K.  I trimmed any excess fabric off the patch on the inside close to the stitching.


 My second darn. This was a smaller hole so didn't put any fabric behind it.


The 222K was designed as a darning machine, it was something that everyone did, darn and repair.  They didn't just throw clothes away because they had a hole in.  They repaired them.  It will be brilliant at repairing vintage table cloths etc.  Will have a go and let you see the results.

Happy days.

Sharon
PS it took much longer to write this post than it did to darn the trews!  Hope it makes sense! Any questions just leave a comment and I will do my best to answer.





4 comments:

  1. That's very ingenious! I have never seen that darner attachment. I repair my husband's work clothes but my repairs do not look as good as yours.

    ReplyDelete
    Replies
    1. Hi Deborah, forgot to say this foot and hoop is especially designed for the 222, they won't fit any other Singer machine. I have darned my jeans on the 221 and 201 using a wooden embroidery hoop, it worked ok but I had to play around with the top tension on both of them. With the 222 I didn't have to touch it. Take care x

      Delete
  2. Nice patching and darning! I love mending jeans. Did some for a customer recently but with this pair the mend was too high up to get to without undoing the side seam. On the Yahoo Vintage Singers group someone asked recently for opinions on whether to keep her 221 or 222, as she was moving. I replied and gave a link to your post about the two machines. Everyone else who replied either said keep both or keep the 222!

    ReplyDelete
    Replies
    1. Thanks Lizzie. I would definitely recommend to keep the 222. I have thought about selling my 221 as I probably won't use her much at all now. But couldn't bring myself to put her on Ebay! x

      Delete

Really love receiving your comments, thank you for your visit to the Button Box